MNT-040010 | Universal Traction Board Mounts | Universal Fitment

Introduction

Follow along in our below linked install guide for the installation of the Universal Traction Board Mounts. If you have any questions, please contact us.

Install Time & Difficulty

10 - 20 minutes

Easy

Tools Needed:

• Crescent wrench or 17 mm wrench
• 3/8 in socket (for included bolts)
• 5/32 inch Allen key (for BuiltRight accessory rail)

Installation 

1. Assembling the Mounts:

• Identify Slots on the Mounting Plates:
  • The two shallower slots are for mounting the pins/bolts for the traction boards.
  • The four deeper slots are for mounting the entire unit to your chosen surface (bed rail, roof rack, etc.).
• Install the Mounting Bolts:
  1. Flip the mounting plate over.
  2. Drop the included bolt into the appropriate slot (the slot will prevent the bolt from spinning).
  3. flip back over, add a washer and thread on the M10 nut. Leave it slightly loose so you can adjust the mount later.
  4. Repeat on the other side for the second mounting bolt.

2. Adjusting for Different Traction Board Sizes:

• Universal and Adjustable Mounting:

  • The mounts are adjustable to accommodate various traction board sizes.
  • Built-in markings for common sizes (e.g., 270 mm center-to-center for MaxTrax boards) help with precise alignment.

• Adjusting for MaxTrax Boards:

  1. Measure the center-to-center distance of your traction board mounting holes (MaxTrax uses 270 mm).
  2. Move the washer and bolt so that the washer’s edge aligns with the appropriate measurement (e.g., the 270 mm mark).
  3. Snug down the bolts once they’re aligned.

• Alternative Option: MaxTrax Pins:

  • The mount is compatible with MaxTrax pins for a quicker release.
  • Install the MaxTrax pin the same way as the bolts. The pin will drop into the slot, and the mount will capture the nut to prevent it from spinning.
  • Tighten at the correct mark (e.g., 270 mm) for the MaxTrax pins.

3. Mounting to BuiltRight Accessory Rails or Other Systems:

• Mounting to Engineering Extrusions:
  1. The mounts can be secured to extrusions, such as BuiltRight’s bulkhead accessory rail.
  2. Use the drop-in nuts or T-slot nuts designed for the extrusion system.
  3. Slide the drop-in nuts into the desired locations, aligning them with the mounting slots on the plate.
  4. Loosely install the bolts and washers to allow for adjustments later.
  5. Once the mounts are aligned and centered, tighten the bolts.

4. Securing Your Traction Boards:

• Using BuiltRight Hardware:

  • Place your traction boards onto the mounting bolts.
  • Tighten the composite knobs down securely.
  • Preload the knobs slightly (a few additional rotations) to prevent rattling during transit.

• Using MaxTrax Pins:

  • Place the traction boards onto the MaxTrax pins.
  • Lock the boards in place by rotating the pins (as per MaxTrax’s design).

5. Alternative Mounting to MOLLE Panels:

• Mounting with Universal Hardware:

  1. If mounting to a MOLLE panel (e.g., BuiltRight Tech Plate), drop the included bolts through the MOLLE slots.
  2. From the backside, secure with a washer and nut.
  3. Repeat for multiple locations (3–4 bolts recommended).
  4. Leave bolts loose until the final position is set, then tighten everything down.

• Using BuiltRight MOLLE Nuts:

  • If using BuiltRight MOLLE panels, MOLLE nuts simplify installation. The nuts hold themselves in place without needing access to the backside of the panel.
  • Insert the MOLLE nuts into the desired locations.
  • Use the included quarter-inch bolts to secure the mount into the MOLLE nuts.
  • Adjust and tighten as needed.

Installation Video